This is a working overview of reverse-phase HPLC, written for readers who want more than a one-paragraph summary but less than a textbook.
Reviewed 2026-03-19. Anything still debated is marked as such rather than presented as settled.
Quality checks after reconstitution include visual inspection, pH measurement, and analytical methods such as reversed-phase high-performance liquid chromatography. These tests can detect insoluble material, degradation products, and changes in concentration. Mass spectrometry is often used to confirm molecular identity when the peptide sequence is known. Because a clear solution can still contain aggregates or modified peptide, visual clarity alone is not sufficient. Analytical results are compared with a reference standard or the pre-reconstitution certificate of analysis.
Container selection matters because peptides can adsorb to glass, plastic, and filter membranes. Low-binding polypropylene tubes reduce losses for hydrophobic sequences, and filtration through a 0.22 µm membrane can remove particulates and microorganisms. Some peptides may bind to certain filter materials, so compatibility should be checked. Aliquots should be prepared before freezing to avoid repeated temperature cycling. Labels should record the peptide identity, lot number, solvent, concentration, reconstitution date, and storage condition.
After a peptide is reconstituted, analytical checks can confirm identity, concentration, and purity. Reverse-phase high-performance liquid chromatography separates the peptide from related impurities and can estimate purity by peak area. Mass spectrometry provides a mass value that supports sequence identity, while ultraviolet absorbance at 214 or 280 nanometers is often used for concentration estimation when the extinction coefficient is known. These methods answer different questions and are complementary. A single measurement rarely establishes full quality, because the same sample can appear acceptable by one method and fail another.
Concentration calculations depend on the amount of peptide present in the vial and the volume of solvent added. Lyophilized preparations often contain counterions, salts, or residual water, so the labeled mass may not equal the mass of the peptide itself. This difference can produce a calculated concentration that is higher than the true peptide concentration. Analytical determination of peptide content, rather than reliance on the vial label alone, reduces this source of error. Uncertainty in volume measurement also contributes, especially when small liquid volumes are handled.
| Property | Value | Notes |
|---|---|---|
| Lyophilized storage | −20 °C or below | Sealed container with desiccant limits moisture ingress. |
| Reconstituted storage | 2 to 8 °C short term | Freezing aliquots at −20 °C or below may extend stability for some peptides. |
| Preferred container | Low-binding polypropylene | Reduces adsorption losses compared with untreated glass. |
| Sterilization method | 0.22 µm filtration | Filter material compatibility should be verified for each peptide. |
| Common label data | Peptide, lot, date, concentration | Supports traceability and avoids repeated freeze-thaw cycles. |
Quality control after reconstitution often includes visual inspection for particulates, pH measurement, and concentration determination by ultraviolet absorbance at 280 nm when aromatic residues are present. Reverse-phase high-performance liquid chromatography can assess purity and reveal degradation peaks. Mass spectrometry confirms molecular identity and detects modifications such as oxidation or truncation. Size-exclusion chromatography can quantify aggregates and oligomers. These methods are established for many peptides but may require optimization for hydrophobic or chemically modified sequences.
Microbial contamination is a concern for aqueous peptide solutions, especially those without preservatives. Bacteriostatic water contains an antimicrobial preservative and is used in some laboratory settings, while sterile water lacks preservatives. Filtration through a sterile filter can reduce particulates and microbes, but some peptides adsorb to filter membranes. The effect of preservatives on peptide stability is peptide-dependent and not fully predictable. Documentation of lot number, solvent, date, and storage conditions supports traceability and reproducibility.
After reconstitution, peptide solutions are generally less stable than lyophilized powders, and hydrolysis, oxidation, deamidation, and aggregation can occur in solution. Stability depends on peptide sequence, concentration, pH, buffer composition, temperature, light exposure, and dissolved oxygen. Many research protocols store reconstituted solutions at 4 °C for short periods or at -20 °C or -80 °C for longer periods. Repeated freeze-thaw cycles can promote aggregation and loss of activity. The optimal storage condition is peptide-specific and often determined empirically rather than predicted from sequence alone.
Once a peptide is dissolved, water becomes a medium for hydrolysis, oxidation, and deamidation. Dry powders often tolerate ambient shipping better than liquid solutions, but the exact stability profile depends on sequence and formulation. Refrigerated storage near 2 to 8 degrees Celsius or frozen storage at minus 20 or minus 80 degrees Celsius is common in laboratories. Repeated freeze-thaw cycles can promote aggregation, precipitation, or loss of activity. Dividing a solution into single-use aliquots before freezing can reduce the number of temperature cycles.
Aseptic technique is used when a reconstituted solution must remain free of microbial contamination. Work surfaces, gloves, and instruments are cleaned, and the septum of a vial is disinfected before solvent is added. A venting needle or pressure equalization can prevent aerosol formation and pressure buildup. Bacteriostatic water contains an antimicrobial preservative, but preservatives can interfere with some assays or alter peptide behavior. Sterile filtration may be used when a formulation cannot be heat sterilized or when particulates must be removed.
Quality control for reconstituted peptides includes recording lot number, solvent, date, and storage conditions. Visual inspection checks clarity, color, and particles, while pH measurement verifies the expected solution environment. Concentration is often estimated by ultraviolet absorbance at 280 nm for peptides containing tryptophan or tyrosine, or by high-performance liquid chromatography. Mass spectrometry can confirm molecular identity before reconstitution. Sterility testing is relevant when microbial contamination would invalidate an experiment, though such testing is not routinely performed in every laboratory.
Of 27 beef burger products tested, 37% were positive for horse DNA, and 85% were positive for pig DNA. Of 31 beef meal products tested, 21 were positive for pig DNA, but all were negative for horse DNA. Nineteen salami products were tested, but were negative for all foreign DNA. Of the 37% of beef products tested positive for horse DNA, Tesco's Everyday Value Beef Burgers tested at 29.1%. All other reported brands had less than 0.3% horse DNA. These products originated from Liffey Meats and Silvercrest Foods in Ireland, and from the Dalepak Hambleton food processing plant in the United Kingdom. Trace amounts of horse DNA were also found in raw ingredients imported from Spain and the Netherlands. Laboratory DNA investigations were requested by the authorities into possible donkey meat adulteration of minced meat products labelled as 100% beef. British company Primerdesign provided many of the tests to laboratories and companies wishing to test for contamination.
Biological precursors of most alkaloids are amino acids, such as ornithine, lysine, phenylalanine, tyrosine, tryptophan, histidine, aspartic acid, and anthranilic acid. Nicotinic acid can be synthesized from tryptophan or aspartic acid. Ways of alkaloid biosynthesis are too numerous and cannot be easily classified. However, there are a few typical reactions involved in the biosynthesis of various classes of alkaloids, including synthesis of Schiff bases and Mannich reaction. Schiff bases can be obtained by reacting amines with ketones or aldehydes. These reactions are a common method of producing C=N bonds. In the biosynthesis of alkaloids, such reactions may take place within a molecule, such as in the synthesis of piperidine: An integral component of the Mannich reaction, in addition to an amine and a carbonyl compound, is a carbanion, which plays the role of the nucleophile in the nucleophilic addition to the ion formed by the reaction of the amine and the carbonyl. The Mannich reaction can proceed both intermolecularly and intramolecularly:
APEKTx1 is a highly selective blocker of the voltage-gated potassium channel Kv1.1 with no effect on other tested potassium channels (Kv1.2, Kv1.3, Kv1.4, Kv1.5, Kv1.6, Shaker IR, Kv2.1, Kv3.1, Kv4.2 and Kv4.3). APEKTx1 selectively blocks Kv1.1 channels with an IC50 value of 0.9 nM, which makes it between a 700 to 3000 times more potent inhibitor than the two known sea anemone peptides targeted against Kv channels (kalicludines and SHTX II). APEKTx1 is thought to interact with Kv1.1 through the aliphatic residue alanine (A352), an acidic residue glutamate (E353), and an aromatic residue tyrosine (Y379), as a mutation in these sites causes a loss in affinity of the toxin for Kv1.1. These residues are located in the H5-loop between the S5 and S6 domains and are part of the channel’s pore. In addition, APEKTx1 acts as a potent trypsin inhibitor (Kd= 124 nM), probably a competitive one. However, trypsin inhibition is more potent (as it has a higher affinity) in BPTI, which can be explained by the presence of Phe13 and Pro19 in APEKTx1, causing an unfavorable interaction.
Sources: en.wikipedia.org
In biochemistry, two biopolymers are antiparallel if they run parallel to each other but with opposite directionality (alignments). An example is the two complementary strands of a DNA double helix, which run in opposite directions alongside each other. Nucleic acid molecules have a phosphoryl (5') end and a hydroxyl (3') end. This notation follows from organic chemistry nomenclature, and can be used to define the movement of enzymes such as DNA polymerases relative to the DNA strand in a non-arbitrary manner.
Five amino acids possess a charge at neutral pH. Often these side chains appear at the surfaces on proteins to enable their solubility in water, and side chains with opposite charges form important electrostatic contacts called salt bridges that maintain structures within a single protein or between interfacing proteins. Many proteins bind metal into their structures specifically, and these interactions are commonly mediated by charged side chains such as aspartate, glutamate and histidine. Under certain conditions, each ion-forming group can be charged, forming double salts. The two negatively charged amino acids at neutral pH are aspartate (Asp, D) and glutamate (Glu, E). The anionic carboxylate groups behave as Brønsted bases in most circumstances. Enzymes in very low pH environments, like the aspartic protease pepsin in mammalian stomachs, may have catalytic aspartate or glutamate residues that act as Brønsted acids.
The Swiss company GlycArt Biotechnology developed a system using CHO cells, where the cells were engineered to overexpress an enzyme called GnTIII. The effect of this overexpression is to block the formation of fucosylated oligosaccharides on the expressed antibodies. This technology was first reported in 1999 and was the basis of GlycArt Biotechnology. Roche acquired GlycArt in 2005 in order to acquire technology to afucosylate antibodies. GlycArt Biotechnology had been founded in 2000 as a spin-out company of the Swiss Federal Institute of Technology in Zurich. The first commercial product from the GlycArt acquisition was obinutuzumab, which as Gazyva gained FDA approval in November 2013 for the treatment of chronic lymphocytic leukemia. Kyowa Hakko Kirin's "Potelligent" platform uses a CHO cell line in which FUT8 has been knocked out, and which produces antibodies with little to no fucose in the Fc region. The company gained marketing approval in Japan in April 2012 for a monoclonal antibody drug called mogamulizumab which was developed using the platform. The Company's technology was first reported in 2004.
Aluminon, the triammonium salt of aurintricarboxylic acid, is a dye often used to detect the presence of the aluminium ion in an aqueous solution. Aluminon forms a red complex salt in combination with Al3+. In addition to its use in qualitative inorganic analysis, aluminon has applications in pigment production. It forms brilliantly colored lake pigments with many metals. The pigments are red in combination with Be2+ and Ga3+. The pigment is deep purple or reddish-brown in combination with Fe3+. Color of a particular pigment in acidic solutions may change: aluminon and Sc3+ form red pigments if the solution is acidic, but otherwise the solutions are colorless. Aluminon is prepared by reacting sodium nitrite with salicylic acid, adding formaldehyde, then treating with ammonia. Analytical chemistry Colorimetry
Sources: en.wikipedia.org
Lipid vesicles or liposomes are approximately spherical pockets that are enclosed by a lipid bilayer. These structures are used in laboratories to study the effects of chemicals in cells by delivering these chemicals directly to the cell, as well as getting more insight into cell membrane permeability. Lipid vesicles and liposomes are formed by first suspending a lipid in an aqueous solution then agitating the mixture through sonication, resulting in a vesicle. Measuring the rate of efflux from the inside of the vesicle to the ambient solution allows researchers to better understand membrane permeability. Vesicles can be formed with molecules and ions inside the vesicle by forming the vesicle with the desired molecule or ion present in the solution. Proteins can also be embedded into the membrane through solubilizing the desired proteins in the presence of detergents and attaching them to the phospholipids in which the liposome is formed. These provide researchers with a tool to examine various membrane protein functions.
There have been many efforts to engineer and improve new AAV variants for both clinical and research purposes. Such modifications include new tropisms to target specific tissues, and modified surface residues to evade detection by the immune system. Beyond opting for particular strains of recombinant AAV (rAAV) to target particular cells, researchers have also explored AAV pseudotyping, the practice of creating hybrids of certain AAV strains to approach an even more refined target. The hybrid is created by taking a capsid from one strain and the genome from another strain. For example:
Network Science, Part 5: Solvent-Accessible Surfaces AREAIMOL is a command line tool in the CCP4 Program Suite for calculating ASA. NACCESS solvent accessible area calculations. FreeSASA Open source command line tool, C library and Python module for calculating ASA. Surface Racer Oleg Tsodikov's Surface Racer program. Solvent accessible and molecular surface area and average curvature calculation. Free for academic use. ASA.py — a Python-based implementation of the Shrake-Rupley algorithm. Michel Sanner's Molecular Surface – the fastest program to calculate the excluded surface. pov4grasp render molecular surfaces. Molecular Surface Package — Michael Connolly's program. Volume Voxelator — A web-based tool to generate excluded surfaces. ASV freeware Analytical calculation of the volume and surface of the union of n spheres (Monte-Carlo calculation also provided). Vorlume Computing Surface Area and Volume of a Family of 3D Balls. GetArea Calculate solvent accessible surface area of proteins online. ProMS ProMS - Protein Molecular Surface Calculator
Sources: en.wikipedia.org
Short-term storage is often at 2 to 8 °C, while longer storage may use frozen aliquots at −20 °C or below. Repeated freeze-thaw cycles should be avoided because they can promote aggregation.
Cloudiness may indicate incomplete dissolution, aggregation, or precipitation. Gentle mixing, pH adjustment, or filtration can sometimes resolve it, but the cause should be identified before use.
Bacteriostatic water contains a preservative that can interfere with some assays or react with certain peptides. Sterile water or a defined buffer may be preferable depending on the downstream application.
Ultraviolet absorbance is common when the peptide's extinction coefficient is known. Reverse-phase HPLC with calibration standards can also estimate concentration. Amino acid analysis or quantitative mass spectrometry may be used when higher accuracy is needed.